Still Running a PCC-II, PCC-III, or Moore 352/353? Preferred Has the Replacement and the People Who Know It

Boiler rooms across the country still depend on loop controllers installed decades ago. Some are Preferred PCC-IIs and PCC-IIIs. Many others are Siemens/Moore 352 and 353 controllers, which Siemens stopped producing in October 2017. When one of these fails, the problem isn’t only finding a part. It’s finding someone who still understands how that controller was programmed.

Preferred solves both. The PCC-IV Digital Loop Controller is the fourth generation of Preferred’s process controllers, built in Danbury, CT, and backed by the same engineering team that supported every generation before it.

Built for the boiler room it’s going into

The PCC-IV is a complete control solution for individual boilers or multiple control loops. One controller can handle several control functions, and its I/O expansion options let you add points later without redesigning the panel.

  • Color touchscreen interface
  • Dual Modbus Ethernet ports, plus Modbus RS-485 for BAS and SCADA integration
  • USB programming port
  • Modern dual-core processor with larger Blockware memory
  • SD card for easy field firmware upgrades
  • Retentive MRAM memory rated for 40-50 years, with no battery and no EEPROM to wear out
  • Service manual mode for hands-on checkout and troubleshooting
  • “Learn” function to speed commissioning
  • Preferred_Draw programming software that is .NET based and no longer relies on the obsolete Visio program

Performance specs include 0.025% accuracy on analog inputs and outputs, 16-bit input and output resolution, and ten execution cycles per second.

PCC-II and PCC-III owners: Preferred still has your back

Preferred treats the support and replacement of older products as seriously as the creation of new ones. That’s why we designed the PCC-IV to seamlessly replace the PCC-III when the hardware is too old to function.

For PCC-III sites, the upgrade is about as simple as a controller change gets:

  • The PCC-IV fits in the same panel cutout as the PCC-III
  • It uses the same expansion boards and the same terminal blocks, so no field wiring changes are required
  • PC4_Draw auto-converts your existing PCC-III program, so there’s no reprogramming from scratch
  • It’s 100% compatible with existing PCC-III links to OITs, SCADA, or BAS, with no Modbus changes required
  • It runs on external 24VDC power while keeping the same 120VAC I/O, and Preferred can supply the 24VDC power supply if your panel doesn’t have one

Preferred also supports PCC-II installations still in the field. Our engineers will review your existing panel and plan the right path to the PCC-IV.

One New York facility shows what that long-term support looks like. The site installed 16 PCC-IIs in 1988, added 17 PCC-IIIs in 1997, and installed 21 more PCC-IIIs in 2002 when it added O2 trim. In 2017, the plant ran a PCC-IV in parallel with one of its PCC-IIIs to observe performance before upgrading the rest. Three generations of controllers, one manufacturer, and nearly 30 years of continuous support.

Siemens/Moore 352 and 353 users: the controller is obsolete, but the knowledge doesn’t have to be

Siemens discontinued the Moore 352, 352PLUS, and 353 loop controllers in October 2017. Since then, many facilities have been living on refurbished spares and repair shops. The bigger problem is people. Most of the technicians fluent in 353 logic have left the workforce, and with them went the configuration software and the know-how to back up or modify a program.

Preferred has that knowledge in-house.

  • In most instances, the PCC-IV can be programmed as a direct replacement for the Moore 352, 352PLUS, and 353
  • The PCC-IV’s capabilities and function blocks are very similar to the Moore controller, so the control approach stays familiar to your operators
  • For less common applications, Preferred has programmers experienced with the Moore 353 who convert your existing Moore function block logic into PCC-IV logic
  • Like the Moore 353, the PCC-IV is a true programmable multiple loop controller, with more room for additional inputs and outputs
  • Its retentive memory lasts five times the lifespan of the Siemens controllers

You get a modern, supported controller without losing the control strategy your plant has relied on for years.

Made in the USA, and supported for the long haul

While other manufacturers discontinue control products or private-label controllers from foreign manufacturers, Preferred keeps designing, building, and supporting its own. Preferred has been in Danbury, CT since 1920, and we’re committed to maintaining loop controller products into the future.

If the PCC-IV isn’t the right fit for your application, Preferred also offers BurnerMate Universal, PWC, and PLC-based systems, along with in-house control logic engineering and panel fabrication.

Ready to replace an aging PCC-II, PCC-III, or Moore 352/353? Contact Preferred to talk with an engineer about your system. Learn more on the PCC-IV Digital Loop Controller page.

Leave a Reply

Your email address will not be published. Required fields are marked *